top of page
Search

How to Metalize a Skull: A Real Metal Finish, Step by Step

Nov 3
8 min read

Affiliate disclosure: Some links in this post may be affiliate links. If you buy through them, I earn a small commission at no extra cost to you — it helps keep the studio running and the tutorials free. I only link to supplies I actually use in my own shop

By Hunter Richardson, Hunter Wyatt Studio, Strasburg, Virginia — skull cleaning and carving for 10+ years.

Quick answer: To metalize a skull, start with a completely grease-free skull. Add 2 coats of primer and let it cure 6 hours. Add 2–3 coats of metal paint — real metal powder suspended in acrylic — dabbing it on to avoid brush strokes, and let it cure 6 hours. Spray your patina on while the second coat is still wet. Finish with a light clear coat, or a colored wax if you used no patina.

A lot of people are looking for something different for their European mounts, and a metal finish is just the thing to give a skull a very classy look. This is not a fake metal lookalike — it involves a real metal finish.

New to skulls entirely? Start with a clean skull first: How to Clean a Deer Skull

Real metal finish — a metalized deer skull with a copper/bronze finish and blue-green patina, antlers left natural
Real metal finish — a metalized deer skull with a copper/bronze finish and blue-green patina, antlers left natural

Materials: You don't need much — brushes, primer, metal paint, patina, and a clear coat or wax, plus gloves (and a respirator if you're spraying). The full list of materials I used, with links to the products, is at the end of this post.

I highly recommend Sculpt Nouveau for the metal paints (I am not being sponsored by the company). Their products are very high quality and the customer service is great. The metal paint consists of fine metal powder suspended in an acrylic. Because it is acrylic based, you can simply wash out your brush after each use. I used the same brush for the bear skull used for this article and just washed it out between each layer of primer/paint.

Before You Start — Three Decisions

The bear skull for this article, clean and grease-free before anything goes on it
The bear skull for this article, clean and grease-free before anything goes on it

  1. The skull has to be free of grease. If there is grease — or any other debris — the metal will not bond to the skull correctly. Get it fully degreased before you start.

  2. Teeth: metalize them or leave them natural? You have the option either way. I personally prefer to metalize them, as it just looks a bit "off" when they are left white. If you want to leave them natural, simply tape them up prior to the process.

  3. Antlers on a buck: keep them natural. Tape up the antlers in order to keep them natural — my personal preference.

Prepped and taped up, ready for primer
Prepped and taped up, ready for primer

B Metal Coating vs. C Metal Coating

There are two types of metal coatings from Sculpt Nouveau:

  • "C" metal coating — has a higher percentage of metal and consists of a body, hardener, and catalyst. It is more intended for objects that will be polished to a higher shine.

  • "B" metal coating — works just fine for skulls and is easier, as there is no need for the hardener and catalyst.

Metal coatings from Sculpt Nouveau include: Silver, Iron, Pewter, Bronze, Brass, and Copper.

Step 1 — Add Primer

Add 2 coats of primer and let cure for 6 hours. You can add the second coat as soon as the first is dry.

For any areas that you can't reach with the paint brush, I just use a spray can of black primer (I just used a generic black primer).

I would highly recommend buying a higher quality paint brush, as the cheaper ones tend to loose bristles — and these can end up sticking on the surface of the skull and creating unnatural lines in the final metal finish.

Brushing on the Prime-It primer
Brushing on the Prime-It primer
Skull and jaw fully primed
Skull and jaw fully primed

Step 2 — Add the Metal Coat

Shake the paint well — the metal dust settles to the bottom of the paint container.

If you are using a sprayer: you will need to strain the paint first, as there can be clumps that will clog the sprayer. Using a sprayer has the advantage of being able to apply a uniform coat. Make sure to thoroughly clean out your sprayer after use. As you will be applying two coats of primer and two coats of the metal paint, you can leave the primer in the sprayer in between the two coats, and the metal paint in between those coats as well.

Add 2–3 coats of metal paint and let cure for 6 hours. You can add the second/third coat as soon as the first/second is dry.

To avoid brush strokes, dab the paint on instead of brushing it on the skull.

Brushing on the Copper B metal coating over the black primer
Brushing on the Copper B metal coating over the black primer
Copper coating complete, before the patina
Copper coating complete, before the patina

Step 3 — Add Patina

While the second coat is still wet, add your patina solution.

There are several options for patina colors, including blue, green, black, brown, etc.

Depending on how humid the climate is where you are will dictate the working time for the wet paint and how long the patina takes to fully cure. The patina will start to work immediately, but it will take a bit to fully work.

If the patina did not activate in an area — this can happen if an area dries before you spray the patina on — simply add a new coat of the metal paint to that area and reapply the patina.

If the patina is too robust, burnish the surface with fine steel wool in order to create a more natural patina, where the metal finish shows through more on the raised areas and the patina stays in the lower/valley areas of the skull's surface.

Spraying the patina onto the still-wet copper coat
Spraying the patina onto the still-wet copper coat
The patina fully worked in - green over copper
The patina fully worked in - green over copper
The patina from above, before burnishing
The patina from above, before burnishing
Burnishing with fine steel wool — copper comes back through on the raised areas, patina stays in the valleys
Burnishing with fine steel wool — copper comes back through on the raised areas, patina stays in the valleys

Step 4 — Add Clear Coat or Wax

Although the metal and patina is rated for outdoor use, I still like to add a light clear coat. Keep in mind the clear coat will lighten the patina slightly. I feel that after I burnish the skull and remove the extra patina, finishing with a clear coat seems to tie everything together and give it a more finished look.

If no patina is added, you can add a colored wax to give an aged look. Simply add the wax on and then wipe off with a rag in order to create an aged/washed out look. The wax has a curing agent in it, so it will harden within a day. If you use a wax, no clear coat is needed.

The finished bear skull — copper metal finish with a green patina, burnished so the copper shows through on the raised areas
The finished bear skull — copper metal finish with a green patina, burnished so the copper shows through on the raised areas
Close-up after burnishing and clear coat — copper on the raised areas, green patina in the valleys
Close-up after burnishing and clear coat — copper on the raised areas, green patina in the valleys
Close-up — the teeth and jaw, metalized along with the rest of the skull
Close-up — the teeth and jaw, metalized along with the rest of the skull
Close-up — nose and teeth in daylight
Close-up — nose and teeth in daylight

Metalizing a Skull — FAQ

Is this real metal, or a fake metal look?

Real metal. The paint is fine metal powder suspended in an acrylic, so the finish on the skull is actual metal — silver, iron, pewter, bronze, brass, or copper, depending on the coating you choose.

Why won't the metal finish bond to my skull?

Almost always grease — or other debris — still in/on the bone. The skull has to be free of grease before you start, or the metal will not bond correctly. Go back and degrease it first.

Should I use the B or the C metal coating on a skull?

The B coating. It works just fine for skulls and is easier — no hardener and catalyst needed. The C coating has a higher percentage of metal and is more intended for objects that will be polished to a higher shine.

Do you metalize the teeth too?

I do — it looks a bit "off" to me when they are left white. If you prefer them natural, tape them up before you start. Same for antlers on a buck: tape them up to keep them natural.

When do you put the patina on?

While the metal coat is still wet. The patina starts working immediately, but takes a bit to fully work — and how humid your climate is affects both your working time and the cure time.

My patina didn't take in one spot. What do I do?

That area probably dried before the patina hit it. Add a new coat of metal paint to that area and reapply the patina while it's wet.

My patina is too strong. Can I tone it down?

Yes — burnish the surface with fine steel wool. That brings the metal finish back through on the raised areas and leaves the patina down in the valleys, which looks more natural.

Clear coat or wax — which finish should I use?

If you used a patina, a light clear coat ties it together — just know it will lighten the patina slightly. If you used no patina, use a colored wax instead for an aged look: wipe it on, wipe it off with a rag, and let it harden (within a day). No clear coat is needed over wax.

Brush or sprayer — which is better?

Both work. A sprayer gives a more uniform coat, but strain the paint first so clumps don't clog it, and clean it thoroughly after. With a brush, dab the paint on instead of brushing, to avoid brush strokes — and buy a good brush, cheap ones shed bristles into the finish.


Materials — The Full List, With Product Links

Everything used on the bear skull in this article — Sculpt Nouveau Prime-It primer, black spray primer for the hard-to-reach spots, Bronze B, Silver B and Copper B metal coatings, Black Wax, and Clear Guard clear coat
Everything used on the bear skull in this article — Sculpt Nouveau Prime-It primer, black spray primer for the hard-to-reach spots, Bronze B, Silver B and Copper B metal coatings, Black Wax, and Clear Guard clear coat

Tools:

  • Brushes — sponge or chip brush (buy a good one — cheap brushes shed bristles into the finish)

  • Paint sprayer (optional)

  • Spray bottle — for patinas

  • Fine steel wool — for burnishing

Products:

Safety:

The Sculpt Nouveau links go to the manufacturer — I'm not sponsored by them, I just use their products. The respirator link is an Amazon affiliate link.


Want to Go Further?

— skull cleaning, staining, metal finishes, and carving, in video.

My book, Skull Carving: Get Skull Carving on Amazon — the complete guide to carving skulls, from prep to finished piece.

Start with a clean skull: How to Clean a Deer Skull


Thanks for learning with me. Now go metalize a skull!

— Hunter Richardson, Hunter Wyatt Studio, Strasburg, Virginia

 
 
 

Comments


  • Instagram
  • Youtube
bottom of page